HomeBuild log

Garage & Code

Automotive tuning, embedded telemetry, and custom fabrication.

Now building

Touge

An Android app for back-road drives: offline maps, twisty routes, group tracking over radio or cell, and automatic GPX recording.

Started September 2026

Latest entry

Oct 1Radios on the bench

Retook the group and radio screens on build 158 with both radios up. 2.4 GHz updates every 1.4 s, the LoRa relay every 3.8 s.

Read the write-up

This post gets updated as the app does.

More projects

Printed parts

Bending a spiderweb tablet mount to failure

A simulated bend test pulls a printed 62 mm socket arm apart, rib by rib. See where the spiderweb cracks, how the new curved wrap flexes, and download either design in four sizes.

Electronics

A dash screen for the R53 bridge, and an SD log that never stops

The R53 K-line and CAN bridge now drives a touchscreen off its USB-C: live gauges, a 20-second graph, the SD log with New log and Mark buttons, and DME read presets. Underneath, it logs every CAN frame and every K-line exchange to the SD card whenever a card is in, and clears its oldest logs when the card fills.

Printed parts

N54 135i intake in CFD: grille snorkels, inlet duct and sealed airbox

My printed N54 intake (grille snorkels, a duct across the radiator support and a sealed airbox around the cone filters) in CFD at the airflow for about 550 whp, and a redesigned duct that loses 28% less before the turbos: 9.2 kPa against 12.8.

Electronics

Pressure CAN node: six pressure sensors and eight inputs on the CAN bus

A board that reads six pressure sensors (four 10 kPa, two 40 kPa, above and below zero) and eight 0–5 V inputs and puts them on the car's CAN bus at 100 Hz, for aero, airbox, turbo-inlet and radiator pressures. Renders, a labelled tour, how to plumb it into a car and the full schematic.

Printed parts

R53 intake in CFD: factory piece against my snout, rear port closed and open

Four versions of the same R53 intake at 240 whp airflow, with flow videos: factory front piece, my printed snout, and my snout with a 3-inch and a 6 by 4.2 inch rear port. Vacuum ahead of the throttle body goes 20.7, 14.4, 6.6, 5.9 kPa. Updated with the new curved-top airbox, which flows the same.

Printed parts

F56 push/pull paddle: one blade, two clicks

A printed two-way F56 paddle with RC bearings, a magnetic click, separate switches and room to reach the original mounting screw. Updated: magnets now replace the springs. Watch the CAD assemble, pull and push.

Printed parts

F56 cold air intake: the whole tract in CFD

CAD views and flow videos of a wider F56 airbox spout at 355 and 563 CFM. The whole intake gains 103 Pa at my logged peak, with a pocket of backward flow inside the spout.

R53 Jarvis: a front corner in 3D

A public R53 Jarvis demo: rotate, pull apart and inspect the driver's front wheel, with an eight-spoke 17-inch reference wheel. Open it right in your browser.

F56 in 3D

My F56 as a hologram you can pull apart: front and rear running gear, underbody, doors, windows and mirrors, with part numbers and available torques, specs and wiring.

Updated Nov 17 Apps

Methanol injection controller

A methanol controller for the MINI F56 that reads boost, RPM, pedal and torque off PT-CAN, learns your pump, carries F56 Code logging over Bluetooth and comes with a round touch screen and an Android app.

Apps

F5X Code

Fault codes in plain English, engine, gearbox and steering logging, module coding and workshop service jobs for the third-generation MINI, from an Android phone and an ENET cable or the red MHD adapter. It flashes too: BMW's JCW GP3 steering profile on a standard F56 rack. Engine fault codes are free, the app is $45 once, and flashing the engine, gearbox or steering is a $25 add-on each.

Apps

PumpWitness

Jackie's first app: log a fill-up from three photos at the pump, get honest MPG for every car, and find out which station's gas keeps running bad.

Electronics

The R53 K-line + CAN bridge — one board that reads the ECU, watches the bus and runs the shift light

The shift light grew a second job, then a third. One board now reads the ECU at 62500, watches the CAN bus, reads the chassis modules and runs the shift light — merging the lot into a single 8.5 Hz stream to the phone. Here is the whole thing: transceiver choice, OBD2 pin colours, the two parts that destroy something if you fit them backwards, every wire drawn in colour, and the PCB it all became.

Apps

TrackEncoder — my glovebox phone records my track video, coaches me live, calls my brake points, and draws the racing line

A $150 Android phone that burns a live coaching overlay into track video, with sound, runs from my pocket over Telegram, calls brake points into my helmet by the circuit's own turn numbers, paints my best lap on the road like a racing game, and hands the session to an LLM that names the three things worth the most time. One post, the whole system, and now every card on the screen explained one at a time: what it tells me in plain English, then the maths underneath it.

Updated Oct 14 Apps

R53 Logger - Flasher

Flash MINI's own Stage 1 from your phone, add the options you want on top, then log the car and see where the tune misses on 3D and cell maps. JCW and GP1 are the Stage 1 flash, the early JCW kit is a Stage 0 for a pulley on stock injectors, and it's on Google Play.

Updated Oct 18 Apps

R53 Coding - Module Coding from Your Phone

NCS Expert, minus the laptop. Seven R53 modules coded from an Android phone, every setting in plain English, and a backup before anything changes. Reading is free, writing is a one-time $30 unlock. Now on Google Play.

Car & track

E82 135i Front Hub Brake Air Shields

Aluminum front hub air shields that replace the E82 factory dust shields — cut flat, bend yourself, CAD on Cults3D for $25

Apps

Mini R53 Logger - Flasher — Heading to the Play Store

R53 Logger - Flasher on Play — live logging, 3D AFR tuning graph, wideband calibration and ECU flash. BETA. Facelift and pre-facelift-conversion ECUs supported for write. App unlock $25, flash $50, Stage 1 flash (OEM JCW / GP1) $50; prepared ECUs $275. Open sign-up.

Apps

Trackday Pyrometer Helper Is Live — Here's the Hardware Behind It

Trackday Pyrometer Helper is on the Play Store — but the real story is the hardware. An open-source BLE pyrometer with printable STLs, a reverse-engineered Tesla TPMS 125 kHz wake coil, and a growing ecosystem of car-guy gadgets you can build yourself.

Printed parts

E82 135i Brake Cooling Ducts — Front & Rear

3D-printed front and rear brake cooling ducts for the E82 135i, plus aluminum deflectors and bumper overlays — design, install, results, and where to buy

Apps

Trackday Pyrometer Helper — User Manual

The complete setup-and-use guide for my track-day app: Bluetooth, the PyroTC gun, TPMS colors, tire inventory, temp sessions, the background monitor, corner balance, and packing lists.